Bantam 2007 1.6 rocam will not start

Asked by Landyguru Jul 21, 2019 at 06:45 AM about the Ford Bantam

Question type: Maintenance & Repair

I have spark, fuel pressure and engine cranks. I
have swapped starter relay. Fuel pump inertia
switch has been disconnected and bridged. Tested
the NTC temp sensor. All is working as it should.
Any suggestions wouls be appreciated.

4 Answers
16,935

Guru97FK8 answered 5 years ago

Check the main starter cable amperage draw. If the Amperage Draw is too high, it will crank but not start. Have you fitted another engine ? You must have the original flywheel for your vehicle on the engine. Your engine has 36 minus 2 teeth for the crank angle toothed rotor, and the older ones have 36 minus 1 teeth.

Mark helpful
10

Guru7GK56 answered 4 years ago

Hi please help I have ford bantam rocam 1.6 it pour lot of petrol an it doesn't start only crank what can be the problem?

1 people found this helpful.
Mark helpful
16,935

Guru97FK8 answered 4 years ago

Check for fault codes . Check the crank angle sensor wiring is possible running right next to the Starter selonoid cable in the same channel. Move the Starter selonoid cable out of the Crank angle sensor Channeling.

Mark helpful

Your Answer:

Related Questions

  • Bantam 2007 1.6 rocam will not start 4 Answers

    I have spark, fuel pressure and engine cranks. I have swapped starter relay. Fuel pump inertia switch has been disconnected and bridged. Tested the NTC temp sensor. All is working as it should. An...

    Ford Bantam

    -

    Maintenance & Repair

  • 2008 Ford Bantam Rocam 1.6 Missfire 2 Answers

    Hi Guys, My 1.6 Bantam Rocam 2008 misses slightly when cold and a lot when it reaches peak heat. i have installed new Spark Plugs, HT Leads, CoilPack, Petrol Pump, Head Gasket and problem is still t...

    Ford Bantam

    -

    Maintenance & Repair

  • ford bantam 1.6 cranks does not start 2 Answers

    i have a ford bantam 1.6 just cranks does not start.battery voltage 12.65v but when i jump start no problem for the whole day where is the problem please help

    Ford Bantam

    -

    Maintenance & Repair

  • Ford bantam rocam engine . Crank no start 1 Answer

    Hi. I have a 2008 ford bantam rocam 1.3. It cranks and has fuel and spark but no start. I'm using a 1.6 ecu for pre 2007 bantams. I also changed the flywheel to match the ecu 36-1 teeth. Does the ...

    Ford Bantam

    -

    Maintenance & Repair

  • Ford Bantam Rocam 1.3 don't want to start 3 Answers

    Ford Bantam Rocam 1.3 don't want to start, could it be the earth wire or relay that is faulty

    Ford Bantam

    -

    Maintenance & Repair

Bantam

Looking for a Used Bantam in your area?

CarGurus has thousands of nationwide listings and the tools to find you a great deal.

Postal Code:

Shortcuts

Search Ford Bantam Questions

CarGurus Experts

  • #1
    Guru97FK8
    Reputation
    15,620
  • #2
    MrRocket12
    Reputation
    1,150
  • #2
    Janus Welgemoed
    Reputation
    1,150
View All

Find great deals from top-rated dealers

Search

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.