Cannot shift after installing slave cylinder?

Asked by kttm15 Jul 15, 2012 at 10:04 PM about the 1987 GMC Sierra

Question type: Maintenance & Repair

I have an 1987 GMC sierra 2500 4WD with a granny gear 4 speed manual transmission. On my way home one
day i lost the use of my clutch completely so i had to drive it home without clutch, found that the slave cylinder had
blown a seal so I replaced the slave and got the feel of my clutch back to normal. Now the problem I'm having is
that the Shifter wont go into any gears, even when the engine is off, the truck is stuck in neutral position. Any ideas
on what to do about this?

195

Patrick answered 12 years ago

if its a hydraulic slave did you bleed it properly would be my first question.

3 people found this helpful.

Mark helpful

kttm15 answered 12 years ago

yes i imagine i did it right, that was what i first suspected but after bleeding it four or five different times for probably 15 minutes each time. i concluded that it probably wasnt that.

2 people found this helpful.

Mark helpful

Krahkr answered 11 years ago

On my 1985 GMC 2500 I had to tilt the slave on a 45 degree angle to bleed it properly.

2 people found this helpful.

Mark helpful

Your Answer:

Cannot shift after installing slave cylinder? 3 Answers

I have an 1987 GMC sierra 2500 4WD with a granny gear 4 speed manual transmission. On my way home one day i lost the use of my clutch completely so i had to drive it home without clutch, found that t...

1987 GMC Sierra

-

Maintenance & Repair
My truck won't get spark after it runs for 20 minutes and you turn it off 2 Answers

I replaced the cap rotor coil ignition switch and distributor and it still doesnt have spark after I shut it off. It will start after sitting for 15 minutes. It's a 6 cylinder gmc sierra 1500 year 9...

1991 GMC Sierra

-

Maintenance & Repair
Truck stalls will not start again after engine warms up 2 Answers

my 1992 gmc sierra truck will start up with no problems when the engine is cooled and been sitting for a while. However after driving it for a bit and the engine gets warm, it stalls and will not re...

1992 GMC Sierra

-

Maintenance & Repair
where is the speedometer wires to the tranny located or where do any speedometer lines, cables or wires hook up period?? curious cause my 99 GMC Sierra has no speed gauge and wont shift outta low gear.... Just had tranny rebuilt do to the input shaft housing busting and leaving it not even wanting it to roll in neutral when running... crazy huh!! just so its said i wasn't the idiot who drove the piss outta it and broke it but first time ive seen um brake like this. anyway besides checking the speedometer hookups what else could it be?? im exhausted and would laugh if it was just a dumb plug, wire or cable unhooked. thanks!! :D 3 Answers

NO Speedometer and wont shift outta low gear!!

1999 GMC Sierra

-

Maintenance & Repair
Why does my truck bogg down or flood out when giving it too much gas? 1 Answer

92 gmc sierra 350 boggs down or floods out after driving it for a few minutes. Once it starts, u can shift to neutral while still rolling down the road, switch truck off and then crank it back up, ...

1992 GMC Sierra

-

Maintenance & Repair

Looking for a Used Sierra in your area?

CarGurus has thousands of nationwide listings and the tools to find you a great deal.

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.

Cannot shift after installing slave cylinder?

3 Answers

Your Answer:

Looking for a Used Sierra in your area?

Shortcuts

Search GMC Sierra Questions

CarGurus Experts

Find great deals from top-rated dealers

Related Models For Sale

Cannot shift after installing slave cylinder?

3 Answers

Your Answer:

Related Questions