The check engine light is on
20 Answers
The Check Engine light is an indicator from the Powertrain Control Module (PCM) that something is out of specs within the computer controlled system. Hook up a scan tool and retrieve the DTCs (Diagnostic Trouble Codes) and go from there. Be aware that a trouble code doesn't necessarily mean that a component is bad except in a few cases. It means that there's a reading or signal that is out of range.
Agree with Tracy. Autozone, Advance, and Oreillys (or other chain parts house) all should offer free diagnostic testing, as well as the part(s) and rental (or for purchase, if you choose) tools to fix it, and might even help or change it for you. Might try plain gas and checking gas cap, as well. Friend had the same problem and did 100% plain fuel and tightened the cap, which corrected it for him (won't always work, wouldn't hurt to try though).
JaredBSpackFordMan answered 11 years ago
My 2002 Ranger was doing the same thing. I attached a code reader to the computer under the steering column and it was able to diagnose the problem as well as its general location. Turned out one particular cylinder(#4) was running LEAN which its cause could be anything from a bad spark plug, to a vacuum or air intake leak, to a timing issue. (Lean=too much air not enough fuel...Rich= the opposite). This at least gave me a starting point, i knew to look for an issue on the cylinder#4 side of the engine. Always look at the simple most likely things first. After a basic, yet thorough, visual and audial inspection of the engine compartment (both with and without the engine running), i was able to locate a pinhole leak in a vacuum line. Simple fix, cost about ten dollars for a quality piece of new vacuum hose, took me about ten minutes to replace and has run great since. Here's my advice, 1) Go to any major auto parts store, and have them pull the vehicle's computer codes. This usually takes about five minutes and is typically free of charge. 2) The code reader will give a basic diagnosis and general area of the problem. It will read something like, for example(when I pulled codes on my Ranger): Cylinder #4 running LEAN. or "This Particular" Sensor is not working or Cylinder #X ignition failure etc. 3) After diagnosis is complete, you should have a better idea of where to begin. During this step, it is very important not to over think your evaluation, its always best to begin with the simplest, most likely causes to that particular problem...If you have no spark, start by checking that the battery is charged and properly installed (even a battery connection that feels tight by hand may NOT be tight enough to make contact "personal experience, embarrassing"), then go to the next step; inspect all wiring relative to the battery, ignition coil, starter, and distributor looking for any loose or corroded connection points and checking the overall condition of wires themselves. Any sign of worn insulation on any wiring may point to a potential trouble area and should be replaced. All this should be checked before you can even consider the plugs themselves being the problem. 4) Once the problem is fixed, you will HAVE to hook up a code reader again to reset the codes/computer. Your check engine light will turn off. If it comes back on, usually while driving, after repairs have been made and codes reset, then you have another problem other than whats just been fixed. Pull the codes and start the process again til all issues are fixed. Note: Code reader is required to reset computer in order to turn off check engine light. Also, check engine light will continue to re-appear until ALL problems are fixed. Just check the codes each time for a diagnosis and go from there.
VACUUM LEAK TEST SHOWS LEAN DO NOT REPLACE YOUR 02 SENSORS ON THE 4.0 you will find 3 elbos 2 are on the passenger side one on drivers side . Ford sells a kit 2 elbos and the tube but also can go to orieilys auto. first elbo to check runs to you maf air intake if this one is not it under the plastic shield on top of your throttle body 3 bolts holding this on but so much more room when you do . 2nd hose down runs around to drivers valve cover check the hose under plastic cover first . can test with brake cleaner or by looking if you are not to old like me . happy motoring :)
Have a ford Ranger showing missing on both one and four cylinder on the exhaust side
I had my Mazda B2300 (same as ranger) engine lights on this morning. This afternoon when I came home from work. I decided to poped that hood open pushed all those vacuum hoses to make sure they are tightly connected... Pushed those spark plugs wires to be sure that they are also tight. I cleaned the battery terminals too. After all was said and done. I started the truck and to my surprise... Baboom the engine lights came on...for a second or two then went away. Test drove the truck for about 70 miles so far soooo good no engines light...to be continued...
Hey, I have a quick question. I own a 1994 Ford Ranger with a manual 5 speed transmission and a six cylinder engine. My check engine light is on also. Before we started driving the car much, it sat for most of that time (except for an occasional drive). Now, in order to drive it more often, however, we had to change the rubber filler tube because it was worn out and cracked. We just had the filler tube replaced about a week ago, but since we bought the car used a year ago, we haven't changed the oil. My mom was driving the car home tonight and the engine started spuddering and the check engine light came on. Anyhow, we checked the engine oil dipstick tonight, and the engine oil is not full. Could that be the problem or is it something potentially more serious?
Get the codes from the computer and go from there. No, the engine oil will not cause a Check Engine light.
Thank you very much, Tracy. I hope it's not going to be an expensive fix.
2009 Ford Ranger check engine light came on ticket AutoZone and it will not read what could be wrong with it
What does code 4 means
Bossmike777 answered 6 years ago
I'm driving a Ford Everest 2010 diesel automatic transmission Check engine is on and I've noticed that my reverse had no power
I have a1994 2.3 with a solid check engine light on
i have a 2001 ford ranger 4.0 the check engine light comes on i live on a dirt road and what i found was the electrical box on the firewall there is a bolt that you loosen and unplug it spray alcohol on both plug ins let dry hook back up light goes off. it gets dust in it and triggers the light to come.. hopes this helps
After working on my radio and A/c my Ford ranger 2002 model 4.0l cannot select gear 3 to 4 please what is the problem I have change new gear box but the problem is still there
I have a 2000 ford ranger 4x4 3.0 that starts sputtering whem i take off and keeps doin it while driving. I changed the fual filter and the sparkplug wires.
MarkMiller123 answered 4 years ago
changed oil and filter, checked all plug wires and vac hoses... no go. last thing was remove battery cable covers and cleaned badly corroded posts and terminals.... bingo! light went off
Guru99C4KN answered 4 years ago
My check engine light on my 2003 Ford Ranger came on and I went to O’Reilly auto parts and asked about checking it. The clerk hooked up a small diagnostic unit to it and it showed that it had a vacuum leak. I asked if it pinpointed it and he said no but it could be a small hole in vacuum line or maybe gas cap. He checked gas cap and it was loose and not tightening up. I had a spare gas cap and put it on. He cleared the check engine light with his diagnostic unit and it was fixed.
Guru9Z9LGL answered 4 years ago
I have a 2012 2.2 ranger check engine lights on as well as all the other lights, but won't start , I plug in OBD 11 & after its run its program it keeps coming back with could not connect ,