No fuel from injectors 1992 5.7 vortec GMC P3500 stepvan

Asked by Gina May 05, 2017 at 10:34 AM

Question type: Maintenance & Repair

Hi all I have a 1992 GMC with a 5.7 Vortec motor. I
have done a full tune-up on it replacing plugs wires
cap and rotor but I did not replace the distributor
itself or the ignition coil pack. It runs fine once it's
started. But it will only start with starting fluid
however last night when I spray starting fluid into
the throttle body it caught on fire and I put it out
with a fire extinguisher. This morning I cleaned up
all the dry chemical from the fire extinguisher and
now I am getting no fuel at the injector into the
throttle body. I do have an access panel so I don't
have to drop the tank to replace the fuel pump
assembly however I can't get the three bolts out
because they are rusted in. My question is does
this sound like the fuel pump assembly or and
injector problem? I have not tested the fuel
pressure because I don't see a fuel rail with a
Schrader valve and I don't have a guage.  Any input
will help immensely because this is my source of
income as it is my food truck and I need to get
back on the road ASAP

3 Answers
223,905

Rowefast answered 7 years ago

Yes, this is a fuel issue. You probably burnt up the connectors to the fuel injectors, just will have to get that back in order. It could be the fuel pump, or the fuel regulator in the TBI needing to be replaced. Wouldn't hurt to do both as I am sure that regulator spring is weak from years gone by and not able to create enough fuel pressure for the injectors. To check fuel pressure you need a fuel pressure gauge set up to check on a TBI system. All it does is connect in the incoming gas line and then to the TBI. Fuel pressure should be 9 to 13 lbs.

1 people found this helpful.
Mark helpful

Gina answered 7 years ago

Thanks for the info but by the time i saw ur reply I had already replaced the pump, the whole assembly unit, and the relay. I had power at the pump, properly grounded so all good there, did an old school trick with a paperclip and got code 54...pulled the relay and sure enough totally corroded. Replaced the relay, bam, she fired right up, fine beautiful mist coming from both injectors into throttle body... all my nails are broken and greased up but my truck is running.;-) only problem remaining is the fuel filter. I bought a new 1 along with the pump etc however I was stripping 1 of the bolts trying to get the old 1 off so I ended up leaving it.

Mark helpful
223,905

Rowefast answered 7 years ago

The fuel filter definitely should be changed. If you can not get it, they make sections of replacement lines for this area of the fuel line. May have to cut it out, and if you use line wrenches would be better for cracking the lines open. You would only need the on line wrench for the nut on the fuel line.

Mark helpful

Your Answer:

Related Questions

  • No fuel from injectors 1992 5.7 vortec GMC P3500 stepvan 3 Answers

    Hi all I have a 1992 GMC with a 5.7 Vortec motor. I have done a full tune-up on it replacing plugs wires cap and rotor but I did not replace the distributor itself or the ignition coil pack. It run...

    GMC

    -

    Maintenance & Repair

  • No fuel from injectors 54 Answers

    I have replace the injectors and rebuilt the fuel pressure regulator and replaced throttle positioning sensor replaced computer and got a noid tester it says possible problem with signal voltage w...

    1991 GMC Sierra 1500 C1500 Standard Cab Stepside SB

    -

    Maintenance & Repair

  • 1997 GMC Sierra 5.7 Vortec 1 Answer

    Just bought a 97 Sierra. Started and ran great when I went to look at it. Apparently it had an engine swap done just before I bought it. Been about a week and 100 miles since then. About 10 starts...

    1997 GMC Sierra 1500 C1500 SLT Extended Cab SB

    -

    Maintenance & Repair

  • 1999 gmc yukon sle 5.7 vortec ecmb fuse hot but does not blow. Replaced fuel pump, harness, and relay. No engine light on and checked all grounds. Any thoughts? 1 Answer

    Fuse won't blow but gets gets so hot it melts! Could it be in the computer? But no engine light on. Starts up every time. Running out of leads.

    1999 GMC Yukon SLE 4WD

    -

    Maintenance & Repair

  • no start on 1999 gmc sierra 1500 4x4 5.3 vortec 1 Answer

    The truck was run in to flood water then pushed out. So when I bought it it came with a diffrent engine and a upper rebuild kit. After doing that then buying new plugs, plug wires, pcm, crank position...

    1999 GMC Sierra 1500 SLT 4WD Extended Cab LB

    -

    Maintenance & Repair

GMC

Looking for a Used GMC in your area?

CarGurus has 17,446 nationwide GMC listings starting at $1,225.

Postal Code:

Shortcuts

Search GMC Questions

CarGurus Experts

  • #1
    yetilikesbeer
    Reputation
    14,180
  • #2
    MikeDaGeek
    Reputation
    14,160
  • #3
    John Saffrahn
    Reputation
    13,000
View All

Find great deals from top-rated dealers

Search

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.