engine swap

by the time you pay for that other motor and go through all the work and get all the kinks worked out it would be cheaper and faster to just buy a gtp.

thing is...the na/3800 I have in there ran hot and is no longer any good. So I have to replace the engine anyway. Figured I'd jus upgrade instead of going back original. I'm can get the 3800 Sc with tranny and pcm,for 2000. I'm jus wondering,will it drop strait in and bolt up? Whats the diff between gtp and base besides engine and exist?

engine and exaust

it will bolt straight up but u have to keep in mind the supercharger if ur grand prix wasnt set up for it u have to try and find the wiring harness with it built in and change the whole harness or go aftermarket sensor to monitor ur boost

what about the tranny? Is the base tranny the same? Thx

02 and a 06,sorry but no it wont work.

sorry again ,no the tranny will not work eather.you got a good idea going but nothing on a 02 will work on a 06.this info is from a guy that owns 3 T-Bird Super Coupes with the 3.8 supercharged engines.so trust me when I say it wont work.sorry.just enjoy your ride.

well,what if I went with an 06 sc3800? Computer and harness would be,all I needed? Just weighing my options. I have gt body and interior that's in A1 condition.But need a engine. Really want the sc3800

sorry not gT but Go

sorry not gT but Gp

sorry,but the sc engine & tranny will onley work in a sc car desigined for it.

Yes I put a super charged 3800 n my 01 pontaic prix gt the motor out of an 02 Bonneville/02 Buick regail gs hd tranny, need gtp pcm or have pcm reprogramed. Had to change fuel injectors, map sensor n passanger side axle

i have a 2002 grand prix se will a 2002 grand prix gtp motor swap?

I have 2002 Pontiac Grand Prix GTP 200,000 plus miles. Runs and drives good. Super charger works good. Just put new plugs control module, cam position sensor, crank position sensor and new factory wiring harness running to all those items. It is getting rusty. Has factory mags. Abs light has been on for awhile. Factory power moon roof and black leather. Great parts or whole. Drive it away for the first $1000 cash. $800. If it is this week. Cole in Wisconsin 53065. The kid drives it everyday. 920-979-0808

i have a 2004 gp gt with a gen 2 3.8 can i put a 2008 3.8 motor in that car

I don't think you'll have any problems with that josh ..... I ended up replacing my 3.8 (06) with a 08 3.8 gen 3 .. All parts where interchangeable

I have a 2005 monte would a 98 3.8 trans ,harness and pcm.will it work ?

1995 GTP is getting gas, there's spark it tries but won't turn over. Any ideas ?

will a motor from a pontiac grandprix2004, be placed in a 2006 pontiac G6

Will a ecm from a 1998 pontiac grand prix gt work in a 2002 pontiac grand prix gt

Can i put a 2004 regal gs supercharger engine in my 2004 grand prix gtp super charger

What sc engines can fit in my 2004 grand prix gtp super charger

I have a 2004 Buick park avenue ultra 3800 sc whole car I also have a 2003 impala ls 3800 will my motor fit from the park ave even those the mounts are different?

Will a 04 Regal 3.8 Non SC Bolt into a 03 Pontiac Grand Prix GT 3.8 Non SC

Will a 1999 Grand Prix gtp engine fit in a 04 Grand Prix

I got a 1999 pontiac grand prix did a 3.8 fit

I got a 1999 pontiac grand prix wil a 3.8 engine will fit

Will a 3500 motor from a 2006 G6 fit my 2006 Grand Prix GTP supercharger with 3.8 engine

I have 3800 engine from a 05 grand prix gt...can i put that engine in a 04-08 grand prix gtp body?

I am currently doing this swap from N/A to supercharged to my 03 Grand Prix GT(donor car was 00 Park Avenue Ultra) All you need to do to swap this engine is as follows; 1. Donor car(has PCM, Engine Transmission, wire harness, Axles) 2. Buy ''L67 swap'' kit from Intense Racing.com or ZZP3800.com(needed are the supercharger bypass connection and MAP sensor extension connection. 3. The supercharger bypass connection goes as follows; On the PCM, undo the CLEAR connections from the PCM and locate PIN '77'(every connection is numbered from 41-81) then with a needle, poke through the orange rubber seal, push PINK wire with pin into PIN 77 socket, connect GREY wire to ''power-on'' source(alternator) then, using electrical tape, cover open wires. 4. Set L67 engine on subframe, attach torque converter to transmission, attach transmission to engine and secure transmission to mount and bolt on the nuts. 5. Using hydraulic jacks and stands, start to jack up the Engine block, Transmission and subframe and attach steering rack to subframe. 6. Start connecting bottom sensor connectors and jack subframe to body of car and install subframe bolts, tighten and torque to spec. 7. Attach Lower intake manifold gaskets, guides, put RTV in all four corners and across the guides, finger tighten bolts, wait 1 hour for RTV to ''cure'' then torque in correct sequence and attach vacuum line. 8. Install pushrods in correct sequence then install head gaskets and the heads, finger tighten all head bolts and then torque in correct sequence following manufacturer specifications and install front exhaust manifold, crossover pipe, shield, rear exhaust manifold and EGR system 9. Install supercharger gasket, install supercharger and bolt it to correct torque spec and connect vacuum lines, throttle cables intake system and all sensor connections. 10. Install fuel rail and bolt it to correct torque spec and attach fuel injector connectors. 11. Attach ALL grounds to body and to transmission. 12. install radiator hoses, attach sensor connectors. 13. Tighten all 3 bolts to Torque converter and torque to correct spec. 14. Attach starter and attach wires, tighten bolts and install dust shield. 14. Attach A/C delete pulley or Attach A/C compressor , plug in sensor connector, attach A/C lines. 15. Make sure every sensor connector is plugged in. 16. Connect battery. 17. Fill Transmission, fill coolant, fill oil. 18. Remove fuel pump relay 19. turn key on and prime oil system, make sure oil pumps from each pushrod and then install valve covers, finger tighten and torque to correct spec. 20. Install upper torque strut mounts and torque the bolts to correct spec. 21. Prime the fuel system, start the car and bleed coolant system of air. 22. Attach front sway bar, mounts and brackets 23. Connect outer tie rods, sway bar links and ball joint from lower control arms, tighten bolts and install cotter pins. 24. Install strut bolts to knuckle and tighten, install brake rotors, caliper bracket, calipers and brake pads. 25. Tighten axle nuts and then torque to correct spec.

Can you put a regular 3800 in a Bonneville that had a 3800 with a supercharge?

Will a 07 3800 work in my 03 grand prix needs a new motor ??

will a 2007 grand prix gt 3800 gt swap for a 5.3 engine in my car ?

Puedo poner un sobre alimentador de un gtp a un motor vortec 4.3?

I have o3 Grand Prix 3.1 I want to put 3800 engine in it's a 07 grand Prix

Will a 3800 motor fit in a mustang car

Is anyone going to answer these guys. I would answer the questions. but I don't know

I have a 2004 Pontiac gtp within 2 weeks I spun a bearing. So I ended up dropping another engine in it. 2000 dollars later. Now I have a woodruff key problem. I cant find one for this car. Does anyone know were I can find a crankshaft woodruff key. And how to get the rest of the old one out. And I'm still driving the car.

I'm trying to ask a question will a 3800 88 Cutlass olds V6 engine work in a 2001 Pontiac grand prix