wheel bearings

75

Asked by Amanda Jul 10, 2008 at 11:40 PM about the 1998 Toyota Corolla LE

Question type: Maintenance & Repair

Anyone have problems with loose front wheel bearings on a 1998 corolla LE? I finally own this car, have owned it for 1 year and this is the only major thing that needs fixed. Mech. wants to charge me $392.00 to fix (parts and labor). Is this something I can do myself, or is the mechanic all right? Car doesn't make any noise, however mech. said I have a month until it really needs done. I would welcome any suggestions/thoughts. Thanks!

8 Answers

530

Hi. I have dealt with the Toyota rear bearing/drum set-up which was the pain in the rear press in/out style caged bearing. On the rear it was an expensive bearing...around 80 bucks. The front should be somewhat the same because it is a front wheel drive but I think on that year it may be referred to as a hub style bearing. Usually a whole unit that has the press in bearing and the hub with all the new wheel studs attached to it. That type of bearing is much more expensive but usually easier to install. Just a couple of bolts and it done. If you have the press in style....real pain for the do it yourselfer.You would need a hydraulic bench press to help do the work for you. $ 392 bucks is a lot of money and I hope he has included the front end alignment in that price as it should be done. Yes you will need the alignment as the old worn bearing could have been shaking the wheel and in turn affect your tie rod end. Also, if you have too...get a second opinion and go to an auto parts store. They can possibly show you what the bearing looks like and the details of what the job may consist of. Good luck! //Charlie

2 people found this helpful.
1,000

get a second opinion, go to a totaly different shop and ask for a safety trip inspection. but it would not be uncommon to need replacement of wheel brgs on a 10 yr old car. they are generally a sealed brg and may have the hub installed on it, that is why they cost more than conventional tapered brgs

1 people found this helpful.
65

Yes you need to get a second opinion. but don't tell them you think somethings wrong, see if they find it. You could do most of the work you self with basic hand tools, well basic tools that most car guys have, but if i remember right you will have to go to a shop to get them pressed in and out. But diss-assembling them yourself will save you some green, but is it worth it? Stuff like that is always better to get professionally done.

the bearings should be sealed in the hub. its cheaper to get a new hub. its easy to do but at the same time its a pain in the ass. a shadetree like you can do it.

2 people found this helpful.

usually bearings dont get loose. when they're bad they're noisy for a few to several years, then they lockup on ya. if the hub is loose, then titen them or get heli coils. by the way the big nut you see in the middle of the hub holds the cv-shaft in. its not a bearing nut. i'm not a mechanic but i've done this several times on my own cars and i got 2.5 years of college on cars from triton college.

1 people found this helpful.
45

if the axle nut is not torqued properly your bearing will fall apart. the axle on the in side with the nut on the outside hold it together. if they are lose, check for the proper torque. if that doesn't help, get new.

1 people found this helpful.
75

Thanks for the advice... I have a friend who works on cars and wanted to do it but said I'd need a hydraulic press to do it, so I'd have to take it to a mechanic. I have never worked on cars myself and don't know how things go together, but I know a little about fluids and basic stuff. It is the front right bearing that is loose. I did go to a second mechanic and he was about the same price, however he said both front wheel bearings were loose. This is parts and labor. Right now the car has started to burn oil so I'm probably just going to trade it in in a year and get a new car.

1 people found this helpful.

just to let you know, fwd uses a hub nut, rwd uses a castle nut or no nut, and 4x4 goes either way. dont get them mixed up

Your Answer:

Corolla

Looking for a Used Corolla in your area?

CarGurus has 2,431 nationwide Corolla listings starting at $4,690.

Postal Code:

CarGurus Experts

  • #1
    Jeff Polhemus
    Reputation
    3,440
  • #2
    Gene Arnett
    Reputation
    3,280
  • #3
    hashimmir
    Reputation
    2,520
View All

Find great deals from top-rated dealers

Search

Related Models For Sale

Used Toyota Camry
63 Great Deals out of 1,075 listings starting at $3,995
Used Honda Civic
201 Great Deals out of 4,060 listings starting at $440
Used Honda Accord
56 Great Deals out of 997 listings starting at $2,000
Used Toyota RAV4
109 Great Deals out of 2,713 listings starting at $2,500
Used Toyota Tacoma
47 Great Deals out of 1,068 listings starting at $9,998
Used Honda CR-V
85 Great Deals out of 4,517 listings starting at $440
Used Hyundai Elantra
153 Great Deals out of 4,244 listings starting at $100
Used Toyota 4Runner
19 Great Deals out of 301 listings starting at $10,800
Used Nissan Sentra
61 Great Deals out of 1,726 listings starting at $1,995

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.