How do you program the garage door buttons in the QX56 2005

Asked by TruckOwner2013 Jun 07, 2013 at 09:28 PM about the 2005 INFINITI QX56 4WD

Question type: General

1 Answer

305

PROGRAMMING HOMELINKT 1. To begin, press and hold the two outer HomeLinkT buttons (to clear the memory) until the indicator light s1 blinks (after 20 seconds). Release both buttons. 2. Position the end of the hand-held transmitter 1 - 3 inches (26 - 76 mm) away from the HomeLinkT surface. 3. Using both hands, simultaneously press and hold both the HomeLinkT button you want to program and the hand-held transmitter button. DO NOT release the buttons until step 4 has been completed. 4. Hold down both buttons until the indicator light on the HomeLinkT flashes, changing from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flashing light indicates successful programming. To activate the garage door or other programmed device, press and hold the programmed HomeLinkT button — releasing when the device begins to activate. 5. If the indicator light on the HomeLinkT blinks rapidly for 2 seconds and then turns solid, HomeLinkT has picked up a “rolling code” garage door opener signal. You will need to proceed with the next steps to train the HomeLinkT to complete the programming which may require a ladder and another person for convenience. 6. Press and release the “smart” or “learn” program button located on the garage door opener’s motor to activate the “training mode”. This button is usually located near the antenna wire that hangs down from the motor. If the wire originates from under a light lens, you will need to remove the lens to access the program button. NOTE: Once you have pressed and released the program button on the garage door opener ’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for convenience to assist when performing this step. 7. Within 30 seconds of pressing and releasing the garage door opener program button, quickly and firmly press and release the HomeLinkT button you’ve just programmed. Press and release the HomeLinkT button up to 3 times to complete the training. 8. Your HomeLinkT button should now be programmed. (To program the remaining HomeLinkT buttons for additional door or gate openers, follow steps 2-8 only.) NOTE: Do not repeat step 1 unless you want to “clear” all previously programmed HomeLinkT buttons.

2 people found this helpful.

Your Answer:

CarGurus Experts

  • #1
    Starr Lehner
    Reputation
    390
  • #1
    GuruWC1LG
    Reputation
    390
  • #3
    Nimrat Jahan
    Reputation
    370
View All

Find great deals from top-rated dealers

Search

Related Models For Sale

Used Nissan Armada
3 Great Deals out of 183 listings starting at $6,999
Used Acura MDX
27 Great Deals out of 773 listings starting at $6,495
Used Cadillac Escalade
24 Great Deals out of 371 listings starting at $6,900
Used Chevrolet Tahoe
22 Great Deals out of 922 listings starting at $11,900
Used GMC Yukon
11 Great Deals out of 947 listings starting at $1,225
Used Lexus GX
3 Great Deals out of 56 listings starting at $13,800
Used Ford Expedition
31 Great Deals out of 822 listings starting at $7,888
Used Toyota Highlander
29 Great Deals out of 737 listings starting at $2,495
Used Dodge Charger
35 Great Deals out of 643 listings starting at $4,888

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.