Reset Check engine light after service

Asked by RonTurrey Nov 27, 2011 at 03:47 PM about the 2001 Nissan Frontier 2 Dr XE Extended Cab SB

Question type: Maintenance & Repair

How do I reset the check engine light now that I have completed the service.

47 Answers

3,970

1.)turn the key to the on position (do not crank over the motor....dont start the engine) 2.) wait 3 seconds.... and then fully step on the gas and let go fully 5 times with in 5 seconds.... (ex. wait...3....stomp.stomp.stomp.stomp.stomp 3.)wait 6seconds....(not steppig on gas pedal) 4. FULLY PRESSS down on gas pedal and hold for about 10 seconds. 5.) the check engine light should be flashing. should be flashing 10times and stop a few seconds and then 10 and stop.....etc. 6. hold down pedal again 10 secs. 7. release pedal.....turn key off..... 8...wait a few seconds and turn the motor on.....check engine light should be gone.

397 people found this helpful.
390

Bad spark plug made my check engine light burn on my 03 Frontier. The kid at the parts store correctly diagnosed #2 plug misfire but refused to turn off the check engine light. New set of NGK Iridium plugs cured the misfire problem and was able to turn off the check engine light with avatar666's very helpful tip.

39 people found this helpful.
460

On older models, disconnect neg battery cable for 24 hrs

46 people found this helpful.
450

Just did what avatar666 suggested on a 2012 nissan frontier sv king cab, worked like magic once I got it right ( after a few tries )... have all my power back and my stupid check engine light / system disablment fixed after the dealership screwed me over by spraying fluid film on my brake spring hold down clips ( which I had to wash off with WD40 ), under the guise of a ' brake inspection'... the adage holds true - if you want it to work, learn to mechanic it yourself

31 people found this helpful.
450

BTW, on the newer models, if you disconnect the battery, it doesn't get rid of the problem I corrected with avatar666s method - less than 24 hours is temporary, more than 24 hours lasts about 3 days... beware of connecting the battery without the key in it, as I got a nasty shock when the alarm started to draw juice... stupid computer nonsense...

14 people found this helpful.
210

Avatar666, this procedure for clearing code worked on my 2002 Frontier XE 3.3 liter.. Thanks !!!

21 people found this helpful.
190

avatar666 it work perfectly on my 05 Nissan Frontier LE 51000 miles.! :) Thanks, Tennesseeduke

19 people found this helpful.
110

Who'd a thunk. Worked on my 2009 Frontier. The light didn't flash, but when I cranked it up, the Service Engine Soon light was gone. Thank you….

11 people found this helpful.
200

I have an 03 Frontier. I tried this 3 times. Not sure what I am doing wrong, but it did not work for me. I plan to take it to an auto parts store and have them run a check on it and see if they can turn it off for me.

20 people found this helpful.
370

Disconnect the battery negative first then positive. Turnkey all the way until it feels like it's going to crank and leave it. Leave it for five seconds and turn key back off position and pull out of ignition. Reconnect the battery positive first then negative start truck no light.

37 people found this helpful.
180

I did what avatar 666 mention and it worked great on my 2006 nissan frontier (62500km) I did exactly what he mentioned and it worked good the second time. Thanks

9 people found this helpful.
310

Reset my light after getting the code and now the SES light is intermittently blinking. Did the reset again and still got the same code as before 1 1 4 0 and still back to blinking again. Any ideas of why this might hapen? Does it really mean there is a serious problem with the car as I have read in other posts? The car is running normal.

31 people found this helpful.
155

Worked like a charm first time. Avatar666 if you're ever in the Boston area drinks on me!

3 people found this helpful.
260

I tried this for months on mine and couldn't get it to work, then I thought how my car works and figured it out: FYI, if you have a manual transmission you need to hold down the clutch pedal also when you do anything with the gas pedal.

26 people found this helpful.
80

Mine did not work s Avatar666 suggested but mine worked as suggested by 211this. I just disconnected the negative battery terminal first, then the positive battery terminal. Then turned the key until it is going to crank, keep the key in that position for 5 seconds and the pull it out. Connect the positive terminal first then the negative terminal. Make sure lights are off. Start the car and the Service Engine Soon light went off.

8 people found this helpful.
50

My 2005 nissan x trail 2.2dci went into limp mode thanks to a bad cam sensor I changed it and it was still in limp mode I tried for days to get it out then tried what avatar666 suggested and problem solved so a massive thanks from me

5 people found this helpful.
70

How do i clear the error code flashing on my audio system for my Nissan Hardbody

7 people found this helpful.
50

Buy a cheap scanner. Harbor Freight has a 30 dollar one. You should do this to better understand why the light is on. It's easy to hook up and operate and can be used on just about any car/truck with what is called a "can" bus. The bus is simply a standard used for signal protocol in numerous industries.

5 people found this helpful.
50

It also worked on my 2003 frontier and I have a standard transmission. Didn't touch the clutch. But I had to try 2 or 3 times to get it to work. Thanks

5 people found this helpful.
10

Wow! Thanks a million! The procedure by avatar666 REALLY worked for my 2005 Frontier 4 cylinder engine with automatic transmission! You are the greatest!!!!!!!

1 people found this helpful.
40

Worked as stated on my 2004 Quest. It did take several tries...seems that the timing has to be spot on so try varying the time after pumping the pedal 5 times to 6 - 10 seconds and it should work. My magic number was 6 seconds. Good Luck! and Thank You! to those who posted this procedure.

4 people found this helpful.
20

Thanks all- yes with a couple of tries and the 6-second timing, this worked great in my 2010 Frontier. My light popped up when I was low on fluid and , despite everything being normal afterwards, the light wouldn't go out. So beware of the PO128 code-like the experts say, check the coolant level first (i.e. before replacing the thermostat)

2 people found this helpful.
120

Did not work on my 2001 Frontier. Tried many times.

12 people found this helpful.

avatar666. Thanks a lot for your help it worked perfect I am so very grateful . Your friend Jerry.

20

Worked! Thank you! (Of course this was after clearing the cause)

2 people found this helpful.
60

Thank everyone for the Tips! PROBABLY WONT BE GETTING THIS KIND OF TRUCK EVEN THOUGH IT MIGHT BE ELECTRICAL PROBLEM?After renting a car and putting 16,000 miles in 8 weeks. I had balled tires, so that made me switch to any vehicle they can off me. To sum it up..they gave me brand new 2018 Nissan truck only put 981.9 miles less than a week diagnostic light pops up. Smh ‍♂️.

6 people found this helpful.
50

I have the best idea take the cluster out remuve the little bulb put some black electric tape problem fixed

5 people found this helpful.
70

How do I turn off SLIP Light long enough to trade in my 07 ??

7 people found this helpful.
20

Worked great on 4.0 in 2017 Frontier! Thanks

2 people found this helpful.
30

Took about four tries but got it turned off. 08 Frontier 4.0L

3 people found this helpful.
30

WTF! ....! It F**king worked. So that's how you check engine light, by stomping stomp stomp stomp stomp stomping it out! Check my engine light now MR. Smog shop Sucks alot tail pipe.

3 people found this helpful.
50

After the reset you will more then likely need to drive your vehicle about 35 miles, then let it cool, then drive 35 more to pass emissions.

4 people found this helpful.
10

Used Avatar666's scheme tonite on my 05 Frontier and it did just fine, second try. Tks, yall! HarveyA

1 people found this helpful.
20

Avatar666's steps do work. I have a 2011 Frontier and the Service Engine Soon light came on after I replaced the positive battery terminal and battery fuse. The above listed steps worked perfectly the first time - and I was REALLY skeptical. It's like hacking a truck!

2 people found this helpful.
10

Cholo. Nissan frontier 2003. I'd like to thanks everyone on this chat for trying to help one to another in a disinterested way. That's is the difference between humans, given from the goodness of their heart. I did almost all the recommendation on this blog to be unsuccessful. Also change new spark plugs, Canister valve purge valve, new gas cap & a tune up (electrical cables etc..) Last night I did what 'Billy' recommended ''On older models, disconnect neg battery cable for 24 hrs". Today I passed the inspection. Thanks everybody!

1 people found this helpful.
10

Thanks avatar666. It worked on my 2007 Frontier. I had to try this about a dozen times before it was successful. In step 3, I ended up waiting 7 seconds rather than 6 seconds and then the rest of the procedure worked as described. It is important to keep your foot on the accelerator for 10 seconds when you see that the SES light is flashing. Initially, I took my foot off prematurely, and had to repeat the procedure. Again, many thanks. My Frontier runs fine.

1 people found this helpful.
30

Did the battery method on my 1998 Nissan Frontier. Worked like a charm!

3 people found this helpful.
20

I also did the battery method on my 2000 Frontier and it worked first try.

2 people found this helpful.
35

2000 Frontier 4 cylinder. Been stomping like that time I was stuck on an anthill in Georgia. My feet are now upset with me and I am nursing a cold one. That yellow light continues to stare at me with it's nefarious glow. I have disconnected the negative terminal on the battery. As I have nothing better to do during the Pandemic, I also ordered the two O2 sensors. We will see how much more damage this will be for my feet and wallet before it is resolved.

3 people found this helpful.
10

Does this reset the codes on your computer meaning you have to go thru a drive cycle after doing Avatar666 solution? Or can you go smog test right after doing so?

1 people found this helpful.

Your Answer:

Frontier

Looking for a Used Frontier in your area?

CarGurus has 878 nationwide Frontier listings starting at $5,998.

Postal Code:

CarGurus Experts

  • #1
    avatar666
    Reputation
    3,970
  • #2
    Mark Gricoskie
    Reputation
    920
  • #3
    jmcalafactor
    Reputation
    770
View All

Find great deals from top-rated dealers

Search

Related Models For Sale

Used Toyota Tacoma
55 Great Deals out of 1,071 listings starting at $8,708
Used Ford F-150
321 Great Deals out of 14,968 listings starting at $1,712
Used Ford Ranger
18 Great Deals out of 1,529 listings starting at $2,888
Used Chevrolet Silverado 1500
202 Great Deals out of 5,975 listings starting at $2,975
Used Toyota Tundra
35 Great Deals out of 1,184 listings starting at $8,500
Used Toyota 4Runner
10 Great Deals out of 304 listings starting at $9,700
Used GMC Sierra 1500
148 Great Deals out of 7,258 listings starting at $3,950
Used Jeep Wrangler
145 Great Deals out of 5,071 listings starting at $5,450
Used Nissan Pathfinder
35 Great Deals out of 1,373 listings starting at $4,333

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.