My brakes lights don't work after installing new proportioning valve in my Ford 63 Galaxie

40

Asked by 63GAX Jan 09, 2014 at 02:49 AM about the 1963 Ford Galaxie

Question type: Maintenance & Repair

Fuses and switch all good, have had that checked. Any solution would be great
Greg

6 Answers

40

Power in is ok and switch is good but have removed switch to find no fluid there and can see valve post across hole any suggestions.

4 people found this helpful.

the right light do's not work and the bulb is good and the wire's are good think it is in the steering weal they told me the two brushes might be wrong way round

60

I had the same problem and fixed it. I will try to explain how to check it and the solution I found. On my 63 Galaxie, it uses a pressure switch, under the hood, on the Master Cylinder. (Most newer cars have the switch on the brake pedal inside the car, not this). I narrowed the problem by1st: Check to see if you have running lights and turn signals. I did have both, which indicated the bulbs were not the problem. Next, you will find two wires going to the pressure switch on the master cylinder. GENTLY remove both wires, you will find posts the fit on. Clean these well. Next, get a jumper wire. Stick the jumper wire in both ends of the two wires you just removed. This will make a circuit (As if the pressure switch was activated). Now check your rear brake lights. You do not have to have the brake pedal pushed or key on. If you brake lights now work, I would say replace the pressure switch. Advance Auto had it in stock!!!! But.....that still wasn't my problem. SO....on the firewall, driver's side, above the master cylinder, you will find two wiring harness plugs. Once again GENTLY wiggle these until they come unplugged. I sprayed PB Blaster and let the sit a few minutes. came right off. I bet you it will be corroded. When I turn the top plug apart, one of the bullet (male connecters) was broken from corrosion. BINGO!!!! I was able to spray PB Blaster in the plug on the firewall where the male connector still inside. After a few minutes, I took a screw, screwed it into the broken connector and was able to pull it out. Next, I cut the wire from the plug. Then I drilled clear through the plug where the broken connector was. I was able to push my wire through the plug I drill, then I was able to put a new bullet (Male) connector on it. I cut the plastic blue shield off of it 1st because it will be inside the plug. I sprayed both plugs to get the corrosion off, then I plugged in the bottom plug. Next I plugged in the new wire I just made, then pushed the plug over the top, plugging in the rest of the wires with the top plug. Next, I jumped the two wires back at the master cylinder. SCORE.....brake lights. I removed the jumper wires, re attached the two wires to the pressure switch, Works like a charm. Bonus....The horn now works!!!!!!!!

6 people found this helpful.
40

67 Ford galaxie new brake light switch installed fuses good have front turn signals and flashers but no brake lights or turn signals or flashers

4 people found this helpful.
10

Hello, My 1964 galaxy brake light on driver side does not work, passenger side works. Could it be the switch on the brake reservoir?

1 people found this helpful.
310,265

No, if one side works but not the other then check lamp socket, lighting grounds on that side, turn signal switch as the switch cancels a brake light to make the turn signals work. Note: turn signal switches are a high fail item.

Your Answer:

Galaxie

Looking for a Used Galaxie in your area?

CarGurus has thousands of nationwide listings and the tools to find you a great deal.

Postal Code:

CarGurus Experts

  • #1
    MrBlueOval
    Reputation
    870
  • #2
    Gene Arnett
    Reputation
    380
  • #3
    James Sparrow
    Reputation
    260
View All

Find great deals from top-rated dealers

Search

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.