No power Running to my engine

Asked by Mamileon14 Apr 19, 2017 at 09:18 PM about the 1996 Chevrolet C/K 2500

Question type: Maintenance & Repair

I have a 96 Chevy C2500. I have already replaced
the battery, fuel pump, gaskets,spark plugs, egm ,
checked fuses, complete tune up. I finally got it
running but when I drive it and accelerate, it doesn't
seem to accelerate as much as it should. Any
ideas on what this might be??

2 Answers
70,965

Kelly answered 7 years ago

i dont see fuel filter and or pressure at the intake.... or cat.. .converter pressure in and out of that also ,....in your list

1 people found this helpful.
Mark helpful

Mamileon14 answered 7 years ago

@Kelly, yes those have been checked and replaced also. And there was a typo in my list. It's not EGM it's the EGR Valve that I replaced last. I can't figure out what it could be.

Mark helpful

Your Answer:

Related Questions

  • No power Running to my engine 2 Answers

    I have a 96 Chevy C2500. I have already replaced the battery, fuel pump, gaskets,spark plugs, egm , checked fuses, complete tune up. I finally got it running but when I drive it and accelerate, it ...

    1996 Chevrolet C/K 2500

    -

    Maintenance & Repair

  • No power 2 Answers

    While jump starting my 96 Fourrunner with a bad starter my 98 Chevy 3/4 ton V8 automatic went completely dead. No radio, lights, ignition. Volt meter shows 12.6V.

    1998 Chevrolet C/K 2500 Cheyenne Extended Cab LB HD RWD

    -

    Maintenance & Repair

  • why is my 5.7 vortec engine idling to low 2 Answers

    97 chevy with 5.7 vortec engine : its idling ruff and low , had it scanned , indicated spider injector needed replacing , had it replaced , starts right up now , still idles ruff and low , but now it ...

    1997 Chevrolet C/K 2500 Silverado Extended Cab LB HD 4WD

    -

    Maintenance & Repair

  • 5.7 Vortec, New Fuel Pump, Has 55 PSI to the rail, New Plugs, Has Spark, Engine Cranks, No Start 9 Answers

    From what I remember before my 96 K2500 wouldn't start, the codes that would show from the OBD II reader were P0301 and P0700. I believe the engine was running ok with no obvious transmission proble...

    1996 Chevrolet C/K 2500 K2500 Cheyenne Extended Cab LB HD 4WD

    -

    Maintenance & Repair

  • no oil pressure, engine runs fine 2 Answers

    So today I took my truck to a friends to get a trailer,hooked up and when I got home the check guage light eas on and my oil pressure was 0. Shut the truck off, checked oil level, full and still lo...

    1995 Chevrolet C/K 2500 Cheyenne Extended Cab 4WD

    -

    Maintenance & Repair

Shortcuts

Search Chevrolet C/K 2500 Questions

CarGurus Experts

  • #1
    Rowefast
    Reputation
    680
  • #2
    Paul
    Reputation
    310
  • #3
    Gene Arnett
    Reputation
    280
View All

Find great deals from top-rated dealers

Search

Related Models For Sale

Used Chevrolet C/K 1500
6 listings
Used GMC Sierra 2500
2 listings

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.