how to remove a starter

Asked by Danielsun Mar 19, 2007 at 04:49 PM about the 1998 Chevrolet S-10 LS LB RWD

Question type: Maintenance & Repair

I tried to remove a stater to put on an oil pan gasket, and the starter won't come out. Any advice on how to get it out?

9 Answers

24,370

Hello Danielsun-- Let me send you to the following site for help removing the starter in your 1998 Chevrolet S-10. There is still a lot of work involved, but hopefully this will answer your question make your job a lot easier. http://autozone.com/servlet/UiBroker?ForwardPage=/az/cds/en_us/0900823d/80/18/b1/3e/0900823d8018b13e.jsp Good luck from Bovan.

25 people found this helpful.
5,135

best bet is to get a repair manual.

6 people found this helpful.
5,315

its a tight fit to remove starter , but most s-10 to get oil pan off you have to raise engine to provide room to remove pan

1 people found this helpful.

Disconnect battery,you need a jack stand and jack, once under truck of blazer same set up, youll see a big aluminum cover w two pole brackets plus 4 or 6 bolts on the sides of this cover. 13 or 15mm. Once cover is extracted. The full veiw of the starter will be avail, the driverside exaust looks like its in the way w some fenaggling you have a close tolerance but will drop out. Disconnect main battery feed from starter,remove purple trigger wire,some rotation of starter will be ness to do this 13mm on batt cable 1/4 or 5/16 on trigger ,oh on rigs that are factory complete have a small braket at the non bussiness end of starter 10mm nut. Removal of this bracket to complete extraction will be ness. Once out of way aim non bussiness end up toward block of engine and begin wiggling the starter out. YOU DID IT VICTORY IS YOURS!!! reverse to install. Clean up ,test, drink beer.

16 people found this helpful.
61,205

it is possible to remove it without taking apart anything else. It is a tight fit but I've done it multiple times. tommcmanis, a 98 doesn't have a removable torque converter cover.

7 people found this helpful.
30

i have starter loose and all bolts out of torque cover or bell housing what ever is that all that is necessary

3 people found this helpful.
10

How can I remove and replace a started on a 2001 Chevrolet Cavalier

1 people found this helpful.

In order to do it have to jack up the trans up a little to get enough room to pull out starter. 13 mm for the big nut and 8mm for the small nut and 15mm for the bolts holding the starter in.

Your Answer:

S-10

Looking for a Used S-10 in your area?

CarGurus has 3 nationwide S-10 listings starting at $12,975.

Postal Code:

CarGurus Experts

  • #1
    Andrew Olsen
    Reputation
    9,860
  • #2
    Robert Smith
    Reputation
    3,420
  • #3
    Gene Arnett
    Reputation
    2,830
View All

Find great deals from top-rated dealers

Search

Related Models For Sale

Used Chevrolet Silverado 1500
202 Great Deals out of 5,975 listings starting at $2,975
Used Ford Ranger
18 Great Deals out of 1,529 listings starting at $2,888
Used Toyota Tacoma
55 Great Deals out of 1,071 listings starting at $8,708
Used Ford F-150
321 Great Deals out of 14,968 listings starting at $1,712
Used GMC Sierra 1500
148 Great Deals out of 7,258 listings starting at $3,950
Used Chevrolet Blazer
19 Great Deals out of 872 listings starting at $19,499
Used Chevrolet Silverado 2500HD
16 Great Deals out of 1,285 listings starting at $8,995
Used Nissan Frontier
22 Great Deals out of 878 listings starting at $5,998
Used Chevrolet Camaro
16 Great Deals out of 307 listings starting at $10,500
Used Chevrolet Tahoe
24 Great Deals out of 911 listings starting at $11,900

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.