What are common causes of oil leaks in BMW X5
24 Answers
Crankcase gaskets. Vacuum lines. It could also be from your power steering reservoir. Are any of your fluids low? I would recommend getting under your vehicle, removing the splash shields and an inspection. You may also want to clean the engine with a good degreaser and check for leaks after driving it to pinpoint the source.
LarchmereImports answered 12 years ago
The most common oil leak is from the valve cover gaskets. It is common for power steering leaks from the filter/resevoir assembly, suction and return lines. Clean engine and identifying what type of fluid it is. Remove the plastic trim from the top of the engine, over the valve covers and the engine under body cover to clean and diagnose.
Hmmm. This must be good advice.
Just bought a 2006 X5 4.4i and was enamoured with how clean the inside is. Got it home and 1 week later the Valley Pan Cover starting leaking coolant all over. After digging in and replacing a leaking vacuum pump, I started on disassembly of the engine for the valley pan. It is located under the intake. I also removed the valve covers for new gaskets and added new spark plugs in. There are several gaskets that need to be replaced when removing the intake, valley pan and valve covers (i.e. throttle body, water pipe, etc...). MAKE sure and prepare to do the timing chain cover gaskets (upper) if you remove the valve covers as these can be a source for oil leaks too. Last but not least....check your oil cooler thermostat (not the oil cooler) as this goes into the motor and the gaskets have a tendency to fail. Your bolts to the "stiffening plate" (or oil catcher) are 16mm nuts and bolts and require a short socket extension. The rear bolts are part of the sway bar in the rear so be careful during re-assembly. Great cars/suvs but WOW the trouble you can have finding the oil leaks. Mine has 93,000 miles on it.
DROB43, your post is very helpful. One query- is lower timing case cover (driver side US X5) also a common source of leak? I have a leak from that side which is likely from valve cover gasket but wanted to be ready with parts in case it turns out to be a leak from the lower timing case gasket.
I have read where this lower timing cover can be a source of the issue but I have read more where the Alternator mount bracket (where your arrow is pointing) can be the source of the leak. Apparently there is a rubber seal that can fail and cause a leak. I am about to put mine up on blocks (in the next 3 weeks) and replace the power steering pump which recently started to go and handle the engine oil cooler thermostat (finally) and repair a bad gasket on the oil dipstick tube. Have seen some residue around the heads and am hoping those gaskets are still good. Also have to replace the lower oil pan cover due to some ignorant idiot stripping the threads and then covering it up with some special adhesive that "locked" the bolt into place. $300 in parts on that one. If this vehicle did not drive so nice or look this good, I would have already gotten rid of it and found something that is less finicky.
The vehicle indeed drives so well and with much power and looks awesome with staggered 20 inch wheels- I always have a smile on my face when driving it. Mine is a 2005 4.4 sports now at 104K miles. Yes, a mechanic pointed out to me the lower timing cover rarely leaks and he can't remember when he changed it last. He thinks it's very likely the valve cover gasket that's leaking. I did change the alternator bracket, it's seal and the oil cooler seals. One of the alternator bolt had broken off. Taking out the bracket was such a challenging work requiring lifting the engine and removing the differential a little bit. I used the harborfreight engine brace sold for $60. The oil cooler seals are easy. By the way, you can get original BMW parts at this place at fantastic prices -nearly 60% less than dealer prices! http://www.thebmwpartstore.com/
CERACOAT_NANOTECH answered 9 years ago
My recent leak appears to be coming from under the oil filter unit, I just used engine cleaner to identify where it was leaking from, but any ideas what to look for that is common problem.
I had a problems with my bmw x1 2015
venomgts10 answered 9 years ago
My 2008 X5 4.8 is parked in my driveway out of oil. I parked it there last night with the low oil light on, then this morning when I started it I had a light come on telling me not to drive it due to low oil pressure. I added 2 quarts of oil and it came out the bottom somewhere as quick as I was adding it. The oil drain plug is in, so I'm looking for any idea's on what it could be... It's not leaking, it's dumping as quick as the oil is being added. Any idea's?
datgaymonchick answered 9 years ago
@venomgts10 My x5 did the exact same thing. Have you found the cause?
I have the same thing going on as you @venomgts10 did you find the cause?
@datgaymonchick and Mzshaw2. I had the same problem with my 2008 4.8 x5. The source of the leak was the oil cooler thermostat gasket. The seal has been leaking for a long time but finally blow out the other day..I think the cool weather here in Arlington caused the gasket to finally give out.. Oil poured out the bottom when I added oil. Anyway I replaced the seal myself. I couldn't see paying $1500 for a independent mech shop to do it for me. I could imagine how much the dealer would charge for that job.Probably around 2 to 3 thousand. This is the gasket part number. Item number 2 http://realoem.com/bmw/diagrams/ w/p/230.png
datgaymonchick answered 9 years ago
@bigggibb That was very helpful, thanks! We did have lots of cold weather.
No problem, let me know if you have anymore questions.
Engineer_1 answered 9 years ago
Check the intake manifold gaskets and the oil separator.
HAVE A BMW X5 4.1 started to smoke when heated and accelerated by a traffic light after leaving smoke stops, I take it to the dealer and said they were the valve seal gasket's, after that I ask another mechanic who tells me was not engine oil it that smelled that he believed it was something else and now I do not know who to believe.what Mr LarchmereImports make sense.
My valve cover gasket failed after I left the car in freezing weather outside in the winter - I find that in the wointer taking short trips moisture builds up and can be seen on the oil filler cap. What happened was that this sludge built up in the oil breather pipe, froze and caused increased pressure causing the valve cover gasket to blow - well that's my theory ?
dandefries answered 7 years ago
I have a 2011 X5M with 103,00 miles on it. I just recently noticed oil drippings on our driveway. I climbed underneath and found the belly pan was covered in oil. Any ideas what it could be?
2008 bmw 528i oil is o pulleys and slinging on filter housing
2006 bmw x5 3.0, im looking to see how to replace the a/c expansion valve and if I have to take down the dash in order to get it
Boy is this a great question...I have a 2003 BMW X5 3.0 with about 160K miles. It's been my experience that all the gaskets have a tendency to become brittle and leak after time. Some of the repairs necessary can be tackled by the novice mechanic such as myself i.e. valve cover but the most likely sources I have such as the engine oil pan are not. They are labor intensive, require the car to be put on a lift...and cost a fortune to fix. The cost of the parts is a drop in the bucket in comparison to what you will pay for the labor. I love my SAV but I will tell you that it is a money pit.