my 1989 camry has a mechanism located near the rear axle that is in series with the brake lines to the rear wheels. It is rusted so bad it cannot be easily replaced or repaired. What happens if I omit that and run lines straight to the brakes? Will they still work?

Asked by Beastdriver Sep 26, 2013 at 08:16 PM about the 1989 Toyota Camry Deluxe Wagon

Question type: Maintenance & Repair

my 1989 camry has a mechanism located near the rear axle that is in series with the
brake lines to the rear wheels. It is rusted so bad it cannot be easily replaced or repaired.
What happens if I omit that and run lines straight to the brakes? Will they still work? What
is it's function and what difference will it make in functionality?

103,655

Reelin68 answered 11 years ago

Not sure but I think it's a junction box that allows the brake fluid to go in two separate directions. If you omit it, how will you be able to send fluid to both rear brakes? There is usually a main line that comes down the frame into the junction box, then one line to the left, and one line to the right........

Mark helpful

Your Answer:

my 1989 camry has a mechanism located near the rear axle that is in series with the brake lines to the rear wheels. It is rusted so bad it cannot be easily replaced or repaired. What happens if I omit that and run lines straight to the brakes? Will they still work? 1 Answer

my 1989 camry has a mechanism located near the rear axle that is in series with the brake lines to the rear wheels. It is rusted so bad it cannot be easily replaced or repaired. What happens if I om...

1989 Toyota Camry Deluxe Wagon

-

Maintenance & Repair
My temp. indicator on the interior rear view mirror is not working, I have checked the sensor and connection and all seems in order, is there a fuse that controls this item; and if so where is it loca 2 Answers

My interior rear view temp.indicator has stopped working. I have located the sensor and checked connection; all seems well...is there a fuse which protects this item, if so where is it located......

1998 Toyota Camry XLE V6

-

Maintenance & Repair
My 2000 v6 toyota camry turns on but just for a second and goes off right after it goes on. Only when is hot. In the mornings generally it turns on fine for like 15 minutes. Some said to check the fuel pump, and alternator, but they are fine, i think it has to do with the plastic connectors that go in to the camshaft position sensor that are falling apart for so much heat on the sidesn and an electritian man did a new one just the ends so it would connect the sensor tightly, but is going off when the car is on after 15 minutes or so. What should i do? replace the sensor? i can´t find the original connectors 2 Answers

electrical issue i think

2000 Toyota Camry XLE V6

-

Maintenance & Repair
I went to the mechanic who changed the ERG valve in and reset the code. He said its a generic code and he couldn't do anything else. I went to the toyota dealer who said they would have to change the vavle again since that's the code!!! the smog shop couldn't help they don't give detailed info on 2000 and above vehicles. So I need to pass smog and no one can help. it could be anything with the PO 401 code. I need to find out what it is and fix it. it's a 2000 Toyota Camry 4 cylinder. 7 Answers

How hard is it to change the VSV valve? what else could I check and replace it has 200,000 miles.

2000 Toyota Camry CE

-

Maintenance & Repair
I drive a Toyota camry xle 2007. Recently i hit a side of a side walk and d tire got damaged and rim bruised. i changed the tire and noticed the car was swerving to one side so i did the alignment but the car still gradually drifts to the right while in motion. i have tried the alignment at different places but its still d same and i have now be made to understand that the alignment is fine and somthing else must be wrong maybe from the sidewalk incident. please advice what else could make the car to drift/swerve when in motion. Thanks 3 Answers

I drive a Toyota camry xle 2007. Recently i hit the side of a side walk and d tire got damaged and rim bruised. i changed the tire and noticed the car was swerving to one side so i did the alignment...

2007 Toyota Camry XLE V6

-

Maintenance & Repair

Used Honda Accord

44 Great Deals out of 907 listings starting at $2,799

Used Toyota Corolla

120 Great Deals out of 1,950 listings starting at $1,995

Used Honda Civic

159 Great Deals out of 3,391 listings starting at $2,230

Used Lexus ES

6 Great Deals out of 197 listings starting at $4,500

Used Toyota 4Runner

14 Great Deals out of 328 listings starting at $9,900

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.

my 1989 camry has a mechanism located near the rear axle that is in series with the brake lines to the rear wheels. It is rusted so bad it cannot be easily replaced or repaired. What happens if I omit that and run lines straight to the brakes? Will they still work?

1 Answer

Your Answer:

Shortcuts

Search Toyota Camry Questions

CarGurus Experts

Find great deals from top-rated dealers

Related Models For Sale

my 1989 camry has a mechanism located near the rear axle that is in series with the brake lines to the rear wheels. It is rusted so bad it cannot be easily replaced or repaired. What happens if I omit that and run lines straight to the brakes? Will they still work?

1 Answer

Your Answer:

Related Questions