Is it possible for a head gasket to leak only oil to the outside of the head?

200,965

Asked by dandyoun Apr 25, 2013 at 09:39 PM about the 1991 Mitsubishi 3000GT SL FWD

Question type: Maintenance & Repair

While making the 110 mile interstate trip home from work at 80 mph.  Stopped at store
and had oil everywhere.  Had lost around two quarts of oil.  Appears to be coming from
the head gasket on the back bank but hard to really tell because oil is everywhere. No oil
above the head gasket area.  No oil in radiator or water in oil.  No loss of compression
and car still runs fine all except for the oil leak.  Prior to this trip car only used about a
quarter of a quart between oil changes.  204000 miles on car but only about 30000 on
head gaskets.  Any suggestions?

26 Answers

yes. it certainly is, often it's because the gasket has "gone soft" or could luck out and just simply be valve cover gaskets. this could create a situation of "bubblin' loose" head bolts~ Seen oil dripping out of the exhaust manifold bolts (how weird is that). Oil is slippery and can get pratically everywhere, the valve cover gaskets, would be a lot less dramatic, but skads easier than some major modifications~

3 people found this helpful.

hey dandyoun, great hearin' from you in the form of a question, kinda tests the brinksmanship here, don't it?

1 people found this helpful.

It's interesting when we review what makes certain Japanese labels unique, for example Subaru is always 4 wheel drive and H- configuration to keep the center of gravity down. Mazda works hard to put competitive, stylish cars out there, Honda "-git a hoooondaaahie" ad from their introduction as a motorcycle manufacturer has stuck with them to the design of their autos, which are pretty darned good, Nissan will always be Datsun to me, and like Toyota, Mitsubishi just feels like a Zero, burnin' hot onward to a firey self-interest. Had these too, with the gutless "MCA jet" experience of 1980 many common suppliers but a notch less reliable, in my personal experience~ Toyota is the undisputed champ in terms of quality and reliability ~ glad you're dandyoun and can release the angry chimps on you~

3 people found this helpful.
200,965

Thanks judge. Built this one for my fifteen year old son. Bad thing is that I only have one more year to drive it before I hand him the keys. (Will sure miss this car) Guess I will pull the intake and exhaust manifolds in the morning to be able to get a better look.

1 people found this helpful.

The Japanese are more resourceful than the Koreans who are just riding the crest, as they haven't really done their homework but rely on other engineering, like cheating thru a test, eventually are going to get the wrong answer. The style and discipline of the Japanese seems to stick with their auto-making, branching out into other industries like Mitubishi televisions (of which has reliably worked since 1988) big-ass direct CRT~

1 people found this helpful.
6,000

I'd triple check the valve cover gasket to make darn sure before a head gasket job is done. Could clean area, then look for exact origins of leak.

4 people found this helpful.
200,965

Oh yes it does. Y'all always tend to give great advice and I would be a foul not to ask for y'all's help. If it appears to be the heads would you suggest retorgue or would gasket replacement be a better fix.

3 people found this helpful.
200,965

Thanks mrmoony. Will look them over real good. But at first glance there does not appear to be any oil above the exhaust manifolds.

2 people found this helpful.
200,965

Maybe so. But I do like my toys. Better just get it fixed and park it for awhile. Bout time to get back started on my 85 z28. Bad thing is cant seem to get excited about it anymore. Would rather build me one like his but the vr4 model instead of the sl.

2 people found this helpful.
177,545

Another common cause of oil leaks is the oil pressure sending unit. Check that out before pulling heads.

2 people found this helpful.
6,000

If your real gentle u might be able to get valve cover off without hurting the gasket and try to 're torque bolts and put cover back on for no cost.if none off the bolts move in that area, means leak isn't fixed. Assuming that's the problem in the first place. Try to lightly tighten valve cover bolts, butt not too much you'll squeeze the gasket out of place.

3 people found this helpful.
200,965

Thanks tenspeed. The majority of the oil appears to be in the area of the sending unit. Just hard to tell exactly because the oil is everywhere. It must have been blowing out real bad from some where. Will check it first.

1 people found this helpful.
200,965

If I can't figure out where it's coming from I will try that mrmoony. Thanks. I already have new valve cover gaskets ordered just in case I need them. If I do re torque should I do it to spec or go a little over what they call for?

6,000

To specks with all bolts equal. Start from middle and tighten working to the ends at the same time.

1 people found this helpful.

are you using an rtv gasket sealant to do the valve covers?....remember ole' Indian Head Gasket Shellac?...you can still find it.~

1 people found this helpful.

mercurochrome, saccarin, Lead car batteries (todays are antimony alloy), lead balance weights on car wheels? cable speedometer, kick-down linkages? mechanical weight vacuum advances? stuff just goes out of favor before we get a chance to get used to it~

200,965

Use it in the corners around the cam seals. But it's not recommend for the rest of the rubber gasket. Will probably use it on whole gasket this time.

1 people found this helpful.
10

How many hours to replace a valve cover gasket and oil can gasket on a 1999 Mitsubishi 3000GT?

1 people found this helpful.
200,965

For a DIY a couple hours maybe. With oil pan drop the frame support out from under it and the pan will come out easier.

i have just bought 2002 mitsi lancer with a 4G9 engine. Noticed an oil patch on floor a couple of days after purchase, replaced sump gasket and distributor seal, still seeping oil from distributor/block/head area. finally pinpointed the problem to the head gasket. No other problems to indicate blown gasket or cracked head. Did research and found SAAB site describing retorquing head bolts as practically routine maintenance for one of their models, so tried it on my mitsi in accordance with workshop manual specs and sequence. A very simple procedure that took only about an hour, and seems to have fixed the problem absolutely.

Your Answer:

3000GT

Looking for a Used 3000GT in your area?

CarGurus has thousands of nationwide listings and the tools to find you a great deal.

Postal Code:

CarGurus Experts

  • #1
    dandyoun
    Reputation
    3,930
  • #2
    Daniel Foster
    Reputation
    1,740
  • #3
    David Girard
    Reputation
    440
View All

Find great deals from top-rated dealers

Search

Related Models For Sale

Used Mitsubishi Eclipse
13 listings starting at $4,998
Used Mitsubishi Lancer Evolution
3 Great Deals out of 13 listings starting at $21,995
Used Chevrolet Corvette
28 Great Deals out of 1,058 listings starting at $15,871
Used Dodge Stealth
2 listings
Used Ford Mustang
65 Great Deals out of 1,258 listings starting at $4,995
Used Toyota Supra
62 listings starting at $51,977
Used Nissan 300ZX
5 listings
Used Chevrolet Camaro
16 Great Deals out of 307 listings starting at $9,995
Used Acura Integra
5 Great Deals out of 172 listings starting at $30,990

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.