changed fuses but still electrical malfunction?

Asked by GTCmalfunction Jul 29, 2014 at 07:41 PM about the 2004 Chrysler Sebring GTC Convertible FWD

Question type: Maintenance & Repair

Engine made no attempt to turn over.  Tried to jumpstart with no success.  Thought it
might be the fuses, so we changed the fuses.  And it started working, but had to turn for
several seconds before starting up.  Now we think that the fuses went bad, but that the
computer is mental.  Any ideas?

1 Answer

migration_cdaigle197... answered 10 years ago

I had the same issue. Fuse #8 shows as a 20amp fuse... I use a 30amp, just because I'm like that. I would check the relays also... the 3 that are in line with each other are on fuse #8, 1 is transmission relay, 1 is fuel relay and the other is starter relay. as for the computer being mental... there are several reasons the computer would say "yea... um.. NO". There are several control modules in the sebring any one of them could be screwing with the ECU. My first suggestion tho would be the fuses then the relays... then if there's still an issue seek a mechanic or get some C4.

1 people found this helpful.
Best Answer Mark helpful

Your Answer:

Related Questions

  • changed fuses but still electrical malfunction? 1 Answer

    Engine made no attempt to turn over. Tried to jumpstart with no success. Thought it might be the fuses, so we changed the fuses. And it started working, but had to turn for several seconds before...

    2004 Chrysler Sebring GTC Convertible FWD

    -

    Maintenance & Repair

  • i changed the calipers on my 07 sebring and still no brakes 1 Answer

    changed the calipers and bleed them and still no brakes

    2007 Chrysler Sebring

    -

    Maintenance & Repair

  • 2008 convertible malfunction 17 Answers

    When I try to put the top down on my 2008 Sebring, I get a message reading convertible top malfunction. But yesterday I tried it and it worked . Now today the message is there again and it isn’t w...

    2008 Chrysler Sebring Limited Convertible FWD

    -

    Maintenance & Repair

  • 2010 chrysler sebring top malfunction 1 Answer

    My 2010 chrysler sebring top wont go down. When i push the top down button i can hear the motor running, but nothing happens. I get a top malfunction light.

    2010 Chrysler Sebring Touring Convertible FWD

    -

    Maintenance & Repair

  • my seabring convertible top wont work it says its malfunction, 1 Answer

    2010 my convertible top wont work the dash board reads malfunction. I did put more power steering in the cylinder were the spare tire is found but that didnt work, my trunk wonk work automatically e...

    2010 Chrysler Sebring Limited Convertible FWD

    -

    Maintenance & Repair

Shortcuts

Search Chrysler Sebring Questions

CarGurus Experts

  • #1
    Sparky222
    Reputation
    4,970
  • #2
    ces13
    Reputation
    2,860
  • #3
    C Daigle
    Reputation
    2,770
View All

Find great deals from top-rated dealers

Search

Related Models For Sale

Used Ford Mustang
64 Great Deals out of 1,285 listings starting at $4,995
Used Chrysler 300
34 Great Deals out of 509 listings starting at $4,999
Used Chevrolet Silverado 1500
205 Great Deals out of 5,862 listings starting at $2,975
Used Chevrolet Corvette
30 Great Deals out of 1,057 listings starting at $15,871
Used Ford F-150
315 Great Deals out of 15,266 listings starting at $1,712
Used Honda Civic
175 Great Deals out of 3,756 listings starting at $3,495
Used Buick LaCrosse
21 listings starting at $7,495
Used Chrysler Crossfire
3 Great Deals out of 19 listings starting at $8,997
Used Chrysler PT Cruiser
12 listings starting at $4,888

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.