I have A 2000 Dodge Intrepid 2.7 V6 and I drained & changed the thermostat in it bc I had no heat and put antifreeze and water back in let it get warm an still blows ice cold. What do I need to do?

Asked by Wilson2976 Nov 13, 2015 at 07:27 AM about the 2000 Dodge Intrepid FWD

Question type: Maintenance & Repair

It blows ice cold air when turned to
heat and it has never run hot on me
since I bought it but it just blows cold
air when the knob is turned to heat.
Please tell me what I can do next.
Thanks.

224,155

Rowefast answered 9 years ago

Make sure all the air pockets are worked out of the cooling system, and if still blowing cool air, there may be a blend actuator module that may be bad, one other thing would be a plugged heater core.

Mark helpful

Your Answer:

I have A 2000 Dodge Intrepid 2.7 V6 and I drained & changed the thermostat in it bc I had no heat and put antifreeze and water back in let it get warm an still blows ice cold. What do I need to do? 1 Answer

It blows ice cold air when turned to heat and it has never run hot on me since I bought it but it just blows cold air when the knob is turned to heat. Please tell me what I can do next. Thanks.

2000 Dodge Intrepid FWD

-

Maintenance & Repair
Why does my 2000 Dodge Intrepid blows cold when it's turned to heat and we changed the thermostat and it put new antifreeze in and it still blows cold . What do I need to check next. 1 Answer

When I drained the car of the water / antifreeze when I changed the thermostat it was a brownish color and looked like it had darker spots in it like something was mixed in with it.

2000 Dodge Intrepid FWD

-

Maintenance & Repair
I have a 2000 dodge intrepid 2.7 starts and runs fine until it gets to normal operating temp then it spits and sputters even backfires then dies until it cools down and the process repeats whats fix? 1 Answer

I have a 2000 dodge intrepid runs fine until it reaches normal operating temp then starts sputtering and backfiring and dies till it cools down then the process repeats how do I fix this?

2000 Dodge Intrepid FWD

-

Maintenance & Repair
I got a P0340 on my '96 intrepid ES. Cam position sensor. I replaced it, but still no go. Put the diagnostic machine on, and still I get a P0340 code, even with the new sensor. What gives here? 1 Answer

I am only getting one code reading on the OBD reader, and that is the p0340. Not sure what the hell else is wrong, but i am not pushing any other codes. If I blew my timing belt, i am certain I would ...

1996 Dodge Intrepid ES FWD

-

Maintenance & Repair
OK, I also have a 2003 Dodge Intrepid Interceptor, it has been broken down for a little while with what I was told was a hole in the head gasket. I am debating on if it would be better to sell it or try and get someone to repair it for me. I love this car but its just sitting right now. Hoping for some good advice. There are pictures of it in my garage. 6 Answers

after blowing a radiator hose it wouldn't drive far without over heating, but would sit and idle for ever without heating. Mechanic in New Mexico couldn't figure the problem out for a week and after ...

2003 Dodge Intrepid

-

Maintenance & Repair

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.