Chevrolet C/K 20 Questions Any type

1978 Chevy 350 Won't Run

My truck will crank and start when gas dumped down the carburetor. After that it stalls. It will idle as long as I keep dumping gas in the carb. Anyone have any ideas on what could be wrong with it...

Can I Reattach The Clucth Fan Mount On My Waterpump?

After i replaced my waterpump the seal on one side didnt hold, and when it blew it popped the mounting pully off that i attache my clutch fan to. Can i fix this or do i need a new pump?

79' Chevy K20 Custom Deluxe Will Not Turn Over.

I recently bought a 1979 Chevy K20 Custom Deluxe and it will not turn over. The first day I got the pickup, it ran perfectly fine. I drove it about a few miles or so and then it just stopped. No hiccu...

Carburetor Swap

Can I take a carburetor from my 1993 Chevy Silverado and install it in my 1978 Chevy Scottsdale the 78 has a Rochester model a quadrajet carburetor or that's what i think The carb needs to be reb...

78 C20 2main Bolts And 4 Main Bolts Engine Bolt Pattern Disfferences For A ...

ok,well i dont know if its a 2main or 4 main. But do those 2 types of engines have identical bolt patterns like the intake manifold exaust manifold coolant pump fuel pump and acceries(alt power st...

Rear End Swap

What years, 8 lug rear ends with disc brakes will fit my 1986 C20 2wd Chevy truck?

Can I Sell My Classic Truck On Car Gurus

Transmission

I am planning on buying a 1976 Chevrolet c20. It has a 3 speed manual transmission. The owner says that it's not best to take it down the highway at 70, since 55mph is about all it can do. He says i...

No Power To Hazard Flasher On Fuse Panel Underdash, Key On, Hazard Switch O...

I had an emergency and when I activated my hazard switch, by pulling it out, nothing happend. I checked the fuse panel prongs (two) where the hazard flasher plugged in, and no power. I turned on the...

82 Chevy C20 Starts Won't Stay On

I'm working on a 82 chevy c20, recently have done all spark plugs, spark plug wires, distributor cap, starter, alternator, alternator plug, battery, and the truck starts runs for awhile then dies....

Battery Gauge Don't Move

I have a 95 chevy c20 pickup with battery gauage that don't move lights bright starts fast no drag got dash lights turn signal been driving this way for 5 days could truck be charging battery

What Is This -pretty Please Tell Me

i dont knnow what this part is and I really am going crazy trying to figure it out, I know it says Chevrolet but I have no idea, it measures 48"x19" I have spent days trying to figure it out, s...

I Have A 1986 Chevy Silverado S20 Pickup That Turns Over And Will Start For...

Have a 1986 Chevy Silverado with 59000 original miles. Has bad bearings and so I only use it once a month to haul trash to the landfill. I rarely use it and when I tried to start it a week ago the b...

Fuel Not Getting Fuel To The Fuel Filter

I got an 81 Chevy Scottsdale K20 four- wheel drive long bed to fuel filter I replace the fuel pump and filled it with gas still no fuel what could it be?

Spark Knock During Acceleration On Incline's

Spark knock during acceleration on inclines

78 C20 2main Bolts And 4 Main Bolts Engine Bolt Pattern Disfferences For A ...

ok,well i dont know if its a 2main or 4 main. But do those 2 types of engines have identical bolt patterns like the intake manifold exaust manifold coolant pump fuel pump and acceries(alt power st...

Wheel Center Bore

Will 8 lug rims from a 2001 chevy silverado 2500 fit my 1977 3/4 ton C20? I know lug pattern matches but will they fit. And where can I find center bore specs on trucks.

Shifting

I have a 1964 Chevy with 350 small block with Saginaw 3 speed ...the truck came with the 3 on a tree is there any way I could keep it or would I have to buy a floor shifter.

1979 K20

I'm actually at a loss, my truck wont turn over or even click at the starter, I have replaced the starter, ignition switch, safety neutral switch, starter relay, fuses, and followed the wiring and ...

Oil Pressure

86 SQUARE BODY 4X4 Just changed oil pump the gauge was reading before change but now its saying i have 0 oil pressure just wondering if anybody has ever had this problem.