ignition switch
495

Asked by scooter_43 Aug 24, 2011 at 11:48 AM about the 2007 GMC Yukon

Question type: Maintenance & Repair

need location of ignition start switch on a 07 Denali

1 Answer
75

GlennA answered 13 years ago

STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2007 GMC Sierra Denali AUTOMOBILES Starter, Replace Vehicle: 2007 GMC Sierra Denali Classic 6.0 V8 GAS 1.Disconnect battery ground cable. 2.Raise and support vehicle. 3.On models equipped with skid plate, remove skid plate mounting bolts and skid plate. 4.On all models, remove front transmission cover bolt. 5.Remove starter motor mounting bolts. 6.Disconnect engine wiring harness electrical connector from oil level sensor. 7.Slide starter forward until it clears transmission, then properly support starter. Avoid cable and wiring damage. DO NOT suspend starter by cables or wires attached to solenoid terminals. Use a rope or mechanics wire to suspend starter. 8.Lower vehicle half way. 9.Remove right front ...

4 people found this helpful.
Mark helpful

Your Answer:

Related Questions

  • ignition switch 1 Answer

    need location of ignition start switch on a 07 Denali

    2007 GMC Yukon

    -

    Maintenance & Repair

  • 2003 GMC Yukon ignition switch 2 Answers

    Put a new ignition switch in and now it won't start. It started before I changed it and now nothing what do I do??

    2003 GMC Yukon 4WD

    -

    Maintenance & Repair

  • My 2005 Yukon ignition switch key 1 Answer

    Could not turn the ignition switch key on finally got it to turn on do you think I need a new ignition key switch

    GMC Yukon

    -

    Maintenance & Repair

  • new ignition switch installed, now engine will not start. rotates with starter, but no ignition 3 Answers

    after new switch (electrical), not the tumbler, , the engine will not start. seems to be with the small timing gear in the ignition switch. is there a witness or timing location for the plastic gear i...

    2002 GMC Yukon SLT

    -

    Maintenance & Repair

  • Ignition lock housing 5 Answers

    I recently replace the lock cylinder the key will turn but it does not start the car when removing the ignition switch the gear inside of the housing does not turn when I move the key

    1996 GMC Yukon

    -

    Maintenance & Repair

Shortcuts

Search GMC Yukon Questions

CarGurus Experts

  • #1
    MikeDaGeek
    Reputation
    9,650
  • #2
    clayduster71
    Reputation
    5,220
  • #3
    David Boccabello
    Reputation
    4,030
View All

Find great deals from top-rated dealers

Search

Related Models For Sale

Used Chevrolet Tahoe
12 Great Deals out of 886 listings starting at $12,900
Used Cadillac Escalade
15 Great Deals out of 433 listings starting at $9,995
Used GMC Yukon XL
10 Great Deals out of 678 listings starting at $7,988
Used GMC Sierra 1500
130 Great Deals out of 6,559 listings starting at $3,975
Used Chevrolet Suburban
11 Great Deals out of 590 listings starting at $10,900
Used Ford Expedition
23 Great Deals out of 832 listings starting at $7,888
Used Chevrolet Silverado 1500
204 Great Deals out of 5,868 listings starting at $2,975
Used Toyota Sequoia
4 Great Deals out of 86 listings starting at $13,989
Used Ford F-150
310 Great Deals out of 14,102 listings starting at $1,712
Used Lexus GX
49 listings starting at $16,495
Used GMC Sierra 2500HD
24 Great Deals out of 1,528 listings starting at $5,500
Used Lincoln Navigator
3 Great Deals out of 171 listings starting at $9,869
Used GMC Acadia
28 Great Deals out of 596 listings starting at $3,300
Used Dodge Durango
58 Great Deals out of 2,246 listings starting at $5,500
Used Jeep Grand Cherokee
124 Great Deals out of 3,187 listings starting at $4,444

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.