Chevrolet S-10 Blazer Questions Maintenance & Repair
Chevrolet S-10 Starting Problems
i have a 1997 chevrolet s-10 4.3, i Change fuel pump, crankshaft sensor, ingnition coil and control module and still dosnt start it will start with starter fluid and then turns off, i need hel asap ...
91 S10 Blazer 4 3l V6 4x4
When I'm building speed or rmps hard I don't hear anything but when I Take my foot off the gas pedal it makes a shering metal on metal noise but goes away when I am building speed and rpms
Turn Signals Not Working Properly.
Rear turn signals work fine except they flash fast, front both sides flash when either side is activated. And it's a 2001 not 94.
1994 S-10 Blazer Stalls Out
My 1994 s-10 blazer has been stalling out. It only happens when it's not under a load. I have recently replaced the fuel pump, distributor cap and rotor, MAP sensor, and taken the battery from a si...
My 91 S10 Blazer 4.3 V6 Tbi
91 s10 blazer 4.3 l v6 4x4 when I start it it turns but have to feather gas pedal to keep running smooth if I take my foot off it runs shitty or dies also when I am driving it around my yard if I h...
What Are Your Thoughts?
Truck is running real rough. I can push the gas petal to the floor and it runs all the way up and sounds good. As soon as I put it in drive it dies. Almost like it’s bogged down. Put it back in pa...
Why Isnt My Right Signal Working?
So, with the lights off, I have all my left signals. Both in the front and the rear. However, I had no right lights with the lights off so i replaced my relay. I now have signals for my left and ri...
Why Isn't My Signal Working?
I have this 91 s10 blazer that has turn signal problems. The left side works fine but the right side doesn't. When the right signal is on, the arrow comes on and stays on, however, neither the fron...
94 S10 Blazer Not Running Right
My 94 s10 blazer drove fine last night with no issues what so ever and fine this morning on my way to work. While breaking my check engine light came on and the oil pressure dropped. I threw it in...
Any Help To Figure This Problem Out Would Be Greatly Appreciated
Just in 2 weeks I replaced the water pump,heater core,coolant temp sensor! It seems since all these parts got replaced now my blazer temp is only getting to 125 degreas,heats in cab but not real h...
1991 Chevy S10 Blazer Starts On 3 To 5 Cylinders
My car has the 4.3 fuel injected. Every time i start it only starts on 3 to 5 cylinders but if i give it a quarter to half throttle for 5 to 10 minutes it catches on all cylinders and is fine. But t...
My Blazer
So my 86 s10 blazer was running after i replaced the coil pack spark plug and wires started no problem had it running and the coil pack fryed ive replaced the coil pack again and same thing idk wha...
2001 Chevy Blazer. Won’t Start Because Of Lack Of Fuel In Throttle Body.
My blazer won’t start unless I pour fuel or ether in the throttle body then it runs fine. I’ve checked and the fuel pump makes noise when I turn on the key but it won’t spray in the throttle body...
Lifters
I have a 94 chevy s10 blazer tahoe lt edition. 4.3L v6 2wd. i went and did an oil change today and on my way home the truck just shut off. i thought i heard a ticking noise but it wasn’t there long...
4l60e No Gears
I have a 93 s10 blazer ..so the problem is when I go the shift into gear lol nothing .. no gears nothing .. I have checked the fluid .saw something about linkage so I'm gonna check that .. but an...
Rear End Swap
Are they anyway that you can take the front rear end of a 99 Blazer and put it in the rear and make it work or are they any difference in them
I Dont Know What Kind Of Wire Harnesses To Buy
I have a 92 st blazer 4 door I want to replace the engine harnesses but dont know the right one to buy any help please
Why Is My Engine Misfiring ?
I replaced my engine in 94 S10 Blazer with a long block 4.3 . It has a miss I can't find. I have changed the plugs , wires , cap and rotor , cleaned injectors and ports . Still misses . I have an ...
How Large Of A Sheet Of Plexiglass?
What are the width and height of the rear glass? Making temp out of plexiglass and don't want to get to big of a sheet.
Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies.