Ford Bantam Questions Any type

Ford Bantam Problems

I drive a ford bantam when the engine is hot it jerks and switches off then I must wait for 10 to 15mins then it drives again

Key Transceiver Loom Replacement And Reprogramming

After replacement of key transceiver loom do I have to reprogram the new transceiver.

Ford Bantam RPM Drops On Revv What Could Be The Problen

Hi i have a bantam rocam 1.3 off gear it its idling is not steady and when i revv it the RPMs just drop completely....please assist

2008 Ford Bantam Crank No Start

I have 2008 Ford Bantam rocam 1.3. It cranks but no start. It has an older computer box used in pre 2007 bantams. I have changed the flywheel to match the ecu as advised and used a 36-1 tooth fl...

Ford Bantam Rocam Engine . Crank No Start

Hi. I have a 2008 ford bantam rocam 1.3. It cranks and has fuel and spark but no start. I'm using a 1.6 ecu for pre 2007 bantams. I also changed the flywheel to match the ecu 36-1 teeth. Does the ...

Ford Bantum Rocam 1.3

My ford bantum rocam gives on but does not want to start or even crank the engine,what l noticed again the is a small red light near the watch that switches on when l turn on the car then off and ...

Ford Bantam 1.6i Xlt Rocam 2011

Kindly assist. I have ford bantam 1.6 xlt rocam 2011 model. It used to jerk while in motion when I accelarated. I was advised to change the coil; spark- plugs and fuel filter of which I did but there...

Why Is My Bantam Not Switches Off After Starting?

My bantam won't switch off After starting what can cause that?

Need Help With A 2008 Ford Rocam 1,3 That Is Hard To Start When Cold

Hi all i recently bought a non runner Bantam with high mileage and decided to completely overhaul the engine, now i am experiencing 2 problems, not sure if its related. Problem 1 the bakkie is hard...

Bantam 1.3 Rocam Feul Problem

My bantam doesn't start when it is warm, it also does not get feul at the injectors in front. We replaced the feul pump and the cranck sensor, but it still does the same? Any suggestions?

2010 Bantam Not Starting But Cranks And Has No Ignition Or Oil Lights

The car started after the top gasket was replaced, after the test drive there was another pipe leaking we replaced that pipe the next day then the car did not want to start, it cranks but no fire, ...

What Might Be The Problem Of My Ford Bantam 1.3i Xl Rocam

I bought a new battery for my Ford Bantam 1.3i xl rocam. After replacing the top gasket and putting everything in order few days then it started having cold start problems.. It's making that sound ...

Clicking / Catching Noise When Turning At Driving Speed - Ford Bantam Rocam...

Hi, I have a ford bantam Rocam 1.3 2003 and have experienced a clicking noise when turning. The noise goes away when pushing the clutch pedal and will not occur when turning off a stand still, only ...

It Just Crank And Not Starting What Could Be The Problem

my 1.6 ford bantam rocam (2008 model) does not start. it crank but no start i checked sparks/fuel they are ok. then i tried to tow it with another car then it start and run smooth.but does not start...

Why Does My Car Back Fire While On Idle

why does my car back fires while engine idles

Why Does My Car's Injectors Not Open

injectors refuse to supply fuel

Power Strain Light Is Flashing

my ford bantam 1.4tdi , starts but no power when excellerating , the power strain light is flashing can someone help on what must i check 2010 model

Interval On Plug Replacement

The service intervals on my 2004 Bantam 1.3 with rocam engine is 15000 km. Must the plugs TR6B-10 also be replaced every 15000 km?? There is no 2004 model option below so I have selected 1995

Why Is My Ford Bantam Not Gin In Gear

I have a 2006 Ford Bantam rocam,it does not want to go in gear when the car is on,the clutch is stiff like always.what can it be please

Where To Find The Indicator Flasher Unit